Vacuum plate-roting 2NVR-5DM1 is designed for pumping from hermetic air vessels and non -aggressive to the working fluid and materials of the design of explosive -fire -haired non -toxic gases, vapors and steam -gas mixtures pre -purified from drip moisture, and mechanical pollution, with an oxygen content no more than in air (21 % in volume) under normal conditions, from atmospheric pressure to the limiting pressure to the limit Residual, at a pressure in the output section not exceeding atmospheric more than 9.3 kPa (70 mm Hg). Vacuum pump 2NVR-5DM1 is made in the climatic design of UHL 4 according to GOST 15150-69, but for operation at ambient temperature and pumped out from 283 to 308 K (from plus 10 ° C to plus 35 ° C).

Vacuum lamellar-roting NACOC 2NVR-5DM1 is a volumetric machine with a drive connected through half a memba. The pump cooling system is air. The pump 2NVR-5DM1 pump is made of aluminum and aluminum alloys, a bronze metal sleeve. Requirements for the quality of electricity under GOST 32144-2013

HACOC 2NVR-5DM1 is seasoned with the working fluid Vacma Oil 100. Monitoring the level of working fluid through the oil indicator, replenishment at the level of the working fluid below the minimum level of the oil indicator.

The principle of operation of the plate-rot vacuum pump 2NVR-5DM1

When rotating the plates with springs pressed to the cylinder, gas absorbed through the input The pipe is supplanted through the exhaust valve due to periodic changes in the volume of the working chamber cavities.

The pump body 2NVR-5DM1 and the electric motor are attached to the rack. The case is simultaneously a container for filling the working fluid, which is designed to compact the working clearances of the rotor mechanism, exhaust valves I and LL steps and the grease of the rubbing surfaces. The working fluid is poured and drained through the holes in the case, covered with plugs and with a seal. The working fluid through the canal in the lid enters the cylinders, cuffs and bearings. The level of working fluid is controlled through the oil indicator. The pipe is attached on the case with a flange, and is compacted with a gasket. It also has a mesh filter.

The exhaust of the vacuum pump 2NVR-5DM1 is carried out through the fittings installed on the case, on the case. The pump has a plug of a gas -forly device, which is sealled by the seal, designed to prevent vapor condensation during pumping vapors and steam -gas mixtures. The cylinders assembled with lids form a working unit of two sequentially connected working chambers-speed chambers. The gas passes from the 1st stage to the second step through the bypass channel in the lid, which is compacted by the seal. The compressed gas sequentially passes both steps and is pushed through the valve, and with large input pressures - additionally through the valve of the 1st stage and then from the body through the fitting is thrown into the outlet for the highway. To the rotor of the 1st stage, the rotation is transmitted from the electric motor through the half-litter, the elastic sleeve-fracture of the half-linker with an elastic sleeve and a key. On the rotor of the II stage, rotation is transmitted through the key.

HACOC 2NVR-5DM1 is equipped with a centrifugal mechanism installed on the half-films and valves that automatically block The pipe in order to preserve the reached residual pressure in the pumped vessel, and also lets atmospheric air into the working chambers, preventing them with working fluid.

Advantages of the vacuum pump 2NVR-5DM1

• The input and output nozzles are transferred to the rapidly detachable connections KF25;
• The mounting of the pump body is carried out by four bolts carried out on its end, which in turn greatly simplifies the process of disassembly/assembly;
• On the basis of the vacuum plate-rot pump 2NVR-5DM1 and a two-rot vacuum pump NVD-200, the AVD-50/5 unit is produced

• PecyPC before the first overhaul of 12500 hours during the service life of 3 years, including the storage period of 1 year in the packaging of the manufacturer in warehouses.

• Warranty life - 12 months with warranty production not exceeding 4500 hours

Components of the vacuum pump 2NVR-5DM1

• 2mo-5 oil separator, installed directly on the output pipe

The operational characteristics of the vacuum pump 2NVR-5DM1

• Environmental temperature, at which it is allowed to operate the pump from 283 to 308 K (from plus 10 ° C to plus 35 ° C).
• The temperature of the pumped medium at the entrance to the pump should not exceed the maximum values ​​of the ambient temperature, in which the pump is allowed.
• Power supply of the pump electric motor from the AC network, 50 Hz. Requirements for the quality of electricity under GOST 32144-2013.
• The pressure of the water vapor in the pumped base should not exceed 3.3 (20) kPa (mm Hg).
• The pressure of the pumped gas at the entrance to the pump during continuous operation should not exceed 133 Pa (1 mm Hg).
• The largest output pressure should not exceed atmospheric by more than 9.3 kPa (70 mm Hg).
• The maximum temperature of the working fluid in the pump during operation should not exceed 353 K (80 ° C).
• The operation of the pump is not allowed at the temperature of the working fluid exceeding 80 ° C.
• The volume of the pumped over hermetic vessel should be no more than 3.5 ms. The resistance of the insulation of the pump of the pump should be at least 0.5 MOM at a voltage of 500 c.
• The circuit breaker for a pump with a three -phase electric motor selects for a rated current 2.5 A with an electromagnetic and thermal release that has a protection class - I according to GOST 12.2.007.0-75
• Sound pressure levels in the octave frequency bands created by the pump at a distance of 1 m from its contour should not exceed the values ​​established by GOST 12.1.003-83

The main parameters of the vacuum pump 2NVR-5DM1

Reviews (0)

Write a review

Your Name

Your Review

Note: HTML is not translated!

Rating   

Bad           Good

Continue

Specification