Electric pumps G2-Opa, G2-OPB, A9-KNA

Electric pumps G2-Opa, G2-OPB, A9-KNA

Electric pumps G2-Op and G2-OPB are designed for pumping milk, juices, beer, wine, water and other liquid foods with a temperature of not higher than 90 degrees C. According to the design, centrifugal pumps are installed without a foundation on three supports on three supports below the level of pumped fluid. The main nodes of the pumps are a case with a working wheel mounted by means of a bracket on a flange of an electric motor. The engine is protected from moisture with a facing casing. The tightness of the pump chamber is carried out by a end seal. All the details of the pumps in contact with the pumped liquid are made of stainless food steel.

the principle of action.

The working wheel, rotating, creates discharge in a hermetically sealed pump chamber. A liquid enters the suction pipeline into the pump chamber, which, under the influence of the operating wheel's blades, begins to rotate and is discarded by centrifugal force to the periphery of the wheel and through the injection pipe enters the pressure pipeline.

technical characteristics

advantages.

- All the details of the pump are made of stainless food steel allowed for the use of the Ministry of Health. This is high -quality steel, which is an analogue of the one that is used today in the production of dishes of leading Western firms.
- The pump wheel is cast, which significantly increases its service life.
- pumps have a quality certificate.

Electric pumps G2-OPD

g2-op g2-Opb
Feed, l/s (m3/hour) 1.8 (6.3) 2.8 (10)
Ples, m 12.5 20
The diameter of the input and output pipes, mm 36 36
Electric motor:
Power, kW 0.75 1.5
The speed of rotation of the shaft is synchronous, C -1 (rpm) 50 (3000) 50 (3000)
Dimensions, mm 505*310*390 520*310*390
Mass, kg 25 35

The self-consuming electric pump G2-OPD is designed to pump milk and similar to the viscosity and chemical activity of food products with a temperature of not higher than 50 degrees C without a gulf of a suction pipeline.

According to the design of the electric pump - centrifugal, unilateral absorption, with closed blades of the working wheel.

The main components of the electric pump: the pump housing, the working wheel, the electric motor, the air separator. All the details of the pump are made of stainless food steel.

The design of the pump allows both collapsible and without collapsible washing with solutions taken in the food industry.

The electric pump cover has a vertically located discharge pipe on which the air separator is mounted. Outside, a bidding pipe is welded to the air separator, to which the discharge pipeline is connected.

The shaft seal is the end. From moisture, the electric motor is protected by a facing casing. Installation of the pump - without a foundation, on three supports.

The working chamber before starting the pump should be filled with a pumped liquid.

A reliable vacuum in a suction pipeline is created as follows. The working wheel, rotating, forms an airborne mixture in the pump’s working chamber, pushes it through the guide nozzle into the air separator, where the liquid is freed from the air and returned back to the pump’s working chamber to form an airborne mixture. This process continues until the necessary vacuum for lifting the fluid is created through the suction pipeline and filling the working chamber of the pump, after which the pump works as centrifugal.

technical characteristics

Electric pump A9-KNA stamp

Horizontal, centrifugal, with a 2-lobed working wheel, monoblock electric pumping unit. Designed for pumping crushed or wiped tomato mass or tomato juice at a temperature of not more than 80 C and kinematic viscosity of up to 20 10-5 m2/s, as well as similar with it in the viscosity and chemical activity of other food products. The pumps of the pump with pitch nuts and nipples. The design of the pump is easily collapsible.

The shaft seal - end. The running part of stainless steel.

g2-OPD
Feed, l/s (m3/hour) 7.1 (25)
Ples, m 20
The diameter of the input and output pipes, mm 50
Electric motor:
Power, kW 55
The speed of rotation of the shaft is synchronous, C -1 (rpm) 50 (3000)
Dimensions, mm 825*365*690
Mass, kg 115

Write a review

Note: HTML is not translated!
   
Bad           Good
0 reviews / Write a review

Request for

feed, m3/hour (l/s) pressure, m. input pair diameter, mm. the diameter of the output pair, mm. power E. DV, rotation frequency, kW, rpm dimensions, mm mass, kg.
20 (5.5) 10 80 50 4.0 1500 FL 595x320x400 62