single-speed centrifugal pumps of sections type; single -flow, for vertical and - depending on the number of steps - horizontal installation and installation at an angle; Mixed and radial flow parts with reduced working wheel diameters controlled by submersible electric motors.
Scope: for pumping clean or slightly contaminated water in the total water supply, sprinkling and watering, lowering or maintaining groundwater levels, increasing pressure, for emergency water supply, in the mountainous industry and fountain plants, etc. The absorption case is installed between the pump and the engine, equipped with a filter to protect the pump from the ingress of rude particles contained in the liquid. Permissible sand content in liquid: 50 g/m³. At the choice with a check valve or an connecting pipe.
Review of technical data
q (50hz)
200.0-2 600 , 0 (m³/h)
h (50hz)
8.0-230, 0 (m)
type of bearing
Sliding undergrowth
hole diameter (inch)
16, 24, 18, 18, 18, 18, 18 26, 20
separation of the case
transverse (radial)
type of work wheel material (according to stand
Jl 1030, CC480K
drive
Elector < /span>
the frequency of the drive engine
50 Hz /60 Hz < /span>
type of drive
Elector < /span>
voltage of the drive engine
low voltage, high voltage < /span>
electric connector
& lt; 6.6 KV, 3 ~
1. Type of working wheel
Diagonal < /span>
the number of inputs of the working wheel
single-flow < /span>
other types of working wheels
Diagonal < /span>
work wheel material (according to the standard E
CC480K, 1.4408, 1.4593 < /span>
type of coupling
directly < /span>
type of lubricant
lubrication of the pumped environment
the material of the pressure case (according to the standard
CC480K, JL 1030
max. Permissible fluid temperature
50.0 (° C) /span>
maximal working pressure
Pn 40
installation of the unit
"Wet" installations
shaft material (according to the standard EN)
1.4021, 1.4462
material case material (according to the standard e
CC480K, JL1030
material of the suction case (according to stand
JL1030, CC480K
characteristics on absorption
non-intercusing < /span>
permissible for drinking water
Yes < /span>
type of accession
Fill < /span>
type of step case
The line of the step with the guide apparatus < /span>
type of suction case
Corps with a ring chamber
body material (according to the standard EN)
CC480K, 1.4408, JL1030, 1.4593
eclass
36410000, 36410106, 36410100 < /span>
installation position
horizontal or vertical
type of shaft seal
end sealing, the shaft sealing ring
body material
Gray cast iron, bronze, stainless steel
max. Working pressure on the pressure sides
35.0 (BAR)
max. Driving power
1000.0 (KW)
type of installation
Stationary < /span>
max. rotation frequency
1750.0 (1/min)
| q (50hz) | 200.0-2 600 , 0 (m³/h) |
| h (50hz) | 8.0-230, 0 (m) |
| type of bearing | Sliding undergrowth |
| hole diameter (inch) | 16, 24, 18, 18, 18, 18, 18 26, 20 |
| separation of the case | transverse (radial) |
| type of work wheel material (according to stand | Jl 1030, CC480K |
| drive | Elector < /span> |
| the frequency of the drive engine | 50 Hz /60 Hz < /span> |
| type of drive | Elector < /span> |
| voltage of the drive engine | low voltage, high voltage < /span> |
| electric connector | & lt; 6.6 KV, 3 ~ |
| 1. Type of working wheel | Diagonal < /span> |
| the number of inputs of the working wheel | single-flow < /span> |
| other types of working wheels | Diagonal < /span> |
| work wheel material (according to the standard E | CC480K, 1.4408, 1.4593 < /span> |
| type of coupling | directly < /span> |
| type of lubricant | lubrication of the pumped environment |
| the material of the pressure case (according to the standard | CC480K, JL 1030 |
| max. Permissible fluid temperature | 50.0 (° C) /span> |
| maximal working pressure | Pn 40 |
| installation of the unit | "Wet" installations |
| shaft material (according to the standard EN) | 1.4021, 1.4462 |
| material case material (according to the standard e | CC480K, JL1030 |
| material of the suction case (according to stand | JL1030, CC480K |
| characteristics on absorption | non-intercusing < /span> |
| permissible for drinking water | Yes < /span> |
| type of accession | Fill < /span> |
| type of step case | The line of the step with the guide apparatus < /span> |
| type of suction case | Corps with a ring chamber |
| body material (according to the standard EN) | CC480K, 1.4408, JL1030, 1.4593 |
| eclass | 36410000, 36410106, 36410100 < /span> |
| installation position | horizontal or vertical |
| type of shaft seal | end sealing, the shaft sealing ring |
| body material | Gray cast iron, bronze, stainless steel |
| max. Working pressure on the pressure sides | 35.0 (BAR) |
| max. Driving power | 1000.0 (KW) |
| type of installation | Stationary < /span> |
| max. rotation frequency | 1750.0 (1/min) |
