UPA pump

UPA pump

Single-stage centrifugal pumps of sections type; Single -flow, for a vertical installation and - depending on the number of steps - a horizontal installation. Radial or mixed flow parts with reduced working wheel diameters controlled by submersible electric motors.
for pumping clean or slightly contaminated water in general water supply, sprinkling and watering, lowering or maintaining groundwater levels, increased pressure, for emergency water supply, in mining and fountain plants, etc. The absorption case is installed between the pump and the engine, equipped with a filter to protect the pump from the ingress of rude particles contained in the liquid. Permissible sand content in liquid: 50 g/m#. For choice with a check valve or an attachment pipe.
Castings:
S 100D, UPA 100C, UPA 150C, UPA 200, UPA 200B, UPA 250C, UPA 300, UPA 350, UPZ, BSX - BSF.

Review of technical data

Write a review

Note: HTML is not translated!
   
Bad           Good
0 reviews / Write a review

Request for

q (50hz) 22.0-1 010 , 0 (m³/h)
h (50hz) 15.0-480, 0 (m)
type of bearing Sliding undergrowth
hole diameter (inch) 14, 08, 10, 10, 10 12, 06
separation of the case transverse (radial)
type of work wheel material (according to stand GJS-400, Cal10FE5NI5, PPO GF30, CUSN10, GJL-200
drive Elector < /span>
the frequency of the drive engine 50 Hz /60 Hz < /span>
type of drive Elector < /span>
voltage of the drive engine low voltage, high voltage < /span>
electric connector & Lt; 6.6 KV, 3 ~
1. Type of working wheel Radial/diagonal
the number of inputs of the working wheel Single-flow < /span>
other types of working wheels Radial/diagonal
work wheel material (according to the standard E Cusn10, CC480K, PPO GF30
type of coupling directly < /span>
type of lubricant Lubrication of the pumped environment
the material of the pressure case (according to the standard jl 1040, jl 1030, CC480K, JS 1030
max. Permissible fluid temperature 50.0 (° C) /span>
maximal working pressure Pn64 < /span>
installation of the unit "Wet" installations
shaft material (according to the standard EN) 1.4462, 1.4021
material case material (according to the standard e JS 1030, JL1030, CC33333G , JL 1040, CC480K, GJL-200, CUSN10, Cual10FE5NI5, GJS-400
material of the suction case (according to stand GJS-400, GJL- 200, Cual10Fe5NI5, CUSN10, JS 1030, JL1030, CC480K
characteristics on absorption Nonamovy. /span>
permissible for drinking water Yes < /span>
type of accession Carving, flanet
type of step case /span>
type of suction case Corps with a ring chamber
classification UNSPSC 4015150300 < /span>
body material (according to the standard EN) GJL-200, JS1030, JL 1030, 1.4593, Cual10FE5NI5, CC480K, 1.4408, CUSN 10, GJS-400, CC333G, JL1030
eclass 3641000000, 36410106, 36410100
installation position Horizontal or vertical
type of shaft seal Part-seal, the sealing ring of the shaft
body material Cast iron, bronze, bronze
max. Working pressure on the pressure sides 57.0 (BAR)
max. Driving power 380.0 (KW)
type of installation Stationary < /span>
max. rotation frequency 3500.0 (1/min)