free-vicre pump CMC and electric pumping on its basis, designed to pump urban and production waste masses and other non-aggressive fluids with a density of up to 1050 kg/m³ of pH = 5-10, with a temperature of up to 90 ° C with a content of abrasive particles up to 5 mm in size, not more than 1% in weight. The maximum concentration of the pumped mass is 8%. The maximum gas content in the pumped environment is 5%.
SMS pumps can be used in other industries, if in their parameters and execution they satisfy the operating conditions and safety in these industries.
Pumps (units) are produced in the climatic performance of UHL, T for operation in rooms of the placement category 4, 2 according to GOST15150.
Pumps (units) are not intended for installation in explosive and fire hazardous rooms.
Condition
SMS 150-125-315 TU 3631-196-05747979-2003 , where: < /p>
">">>
- SMS -Stop-mass troops (free-vikhrev);
- 150 -the diameter of the input pipe, mm;
- 125 -the diameter of the output pipe, mm;
- 315 -the diameter of the working wheel (conditional), mm;
- UHL -climatic execution;
- 4 -Placement category.
Appointment
SMS free-vocal pumps and electric pump units on its basis are designed to pump urban and production waste masses and other non-aggressive liquids with a density of up to 1050 kg/m 3 with pH = 5-10, with temperature, with temperature. Up to 363k (90 ° C) of carrying fairly large extraneous objects and with the content of abrasive particles in size up to 5 mm. no more than 1% by mass. The maximum concentration of the pumped mass is 8%. The maximum gas content in the pumped environment is 5%.
Pumps can be used in other industries, if in their parameters and execution they satisfy the operating and safety conditions in these industries.
Pumps (units) belong to products of the type 1 (restored) according to GOST 27.003-90 and are produced in the climatic performance of UHL for operation in rooms of the placement category 4 according to GOST 15150-69 and climatic design of the placement of placement 2 according to GOST 15150-69.
SMS type pumps and electric pump units on their basis are not designed for installation in explosive and fire hazardous rooms.
Pumps and units are developed taking into account export delivery in accordance with the requirements of OST26-06-2011-79.
Design
SMS type pumps - centrifugal, horizontal, console, with an ELD seal of the shaft.
The SMS pump housing is a cast-iron casting, in which the pump and output pipe, spiral-ring tap and supporting paws are entered. The entrance to the pump is located along the rotation axis, the output pipe is directed vertically upward and is located in the same plane with the wheel axis. SMS pumps and cm are the same.
The working wheel - free -wound type (open), is shifted in the axial direction relative to the spiral body of the pump, which allows the use of a pump for pumping liquids with fairly large foreign objects. The working wheel is attached to the shaft using a celestial nut.
The pump rotor is rotated by the electric motor through the connecting bushing-fan coupling. Rotor supports are two radially - stubborn bearing installed in the bracket.
The direction of rotation of the rotor is right (clockwise), if you look from the side of the electric motor.
The connecting dimensions of the flanges-according to GOST12815-80, type I.
Application
">">>
-
Features/advantages
-
Compared to pumps, cm allowed to work on liquids with sufficiently large impurities. The removal of the working wheel beyond the running part of the pump housing reduces the risk of jamming, and the clogging of the running part
Mark
Feed, m³/h
Ples, m
Permissible cavitation reserve, m
Rotation frequency, rpm
Pump power, kW
Voltage, in
PPD pump, %
The mass of the pump, kg
Pressure at the entrance to the pump, MPa
Current frequency, Hz
SMS 80-50-200
90
60
5
2900
35
220/380
54
75
0.25
50
SMS 150-125-315
200
32
7
1450
46
220/380
57
250
0.25
50
SMS 150-125-315 TU 3631-196-05747979-2003 , where: < /p>
- ">">>
- SMS -Stop-mass troops (free-vikhrev);
- 150 -the diameter of the input pipe, mm;
- 125 -the diameter of the output pipe, mm;
- 315 -the diameter of the working wheel (conditional), mm;
- UHL -climatic execution;
- 4 -Placement category.
Appointment
SMS free-vocal pumps and electric pump units on its basis are designed to pump urban and production waste masses and other non-aggressive liquids with a density of up to 1050 kg/m 3 with pH = 5-10, with temperature, with temperature. Up to 363k (90 ° C) of carrying fairly large extraneous objects and with the content of abrasive particles in size up to 5 mm. no more than 1% by mass. The maximum concentration of the pumped mass is 8%. The maximum gas content in the pumped environment is 5%.
Pumps can be used in other industries, if in their parameters and execution they satisfy the operating and safety conditions in these industries.
Pumps (units) belong to products of the type 1 (restored) according to GOST 27.003-90 and are produced in the climatic performance of UHL for operation in rooms of the placement category 4 according to GOST 15150-69 and climatic design of the placement of placement 2 according to GOST 15150-69.
SMS type pumps and electric pump units on their basis are not designed for installation in explosive and fire hazardous rooms.
Pumps and units are developed taking into account export delivery in accordance with the requirements of OST26-06-2011-79.
Design
SMS type pumps - centrifugal, horizontal, console, with an ELD seal of the shaft.
The SMS pump housing is a cast-iron casting, in which the pump and output pipe, spiral-ring tap and supporting paws are entered. The entrance to the pump is located along the rotation axis, the output pipe is directed vertically upward and is located in the same plane with the wheel axis. SMS pumps and cm are the same.
The working wheel - free -wound type (open), is shifted in the axial direction relative to the spiral body of the pump, which allows the use of a pump for pumping liquids with fairly large foreign objects. The working wheel is attached to the shaft using a celestial nut.
The pump rotor is rotated by the electric motor through the connecting bushing-fan coupling. Rotor supports are two radially - stubborn bearing installed in the bracket.
The direction of rotation of the rotor is right (clockwise), if you look from the side of the electric motor.
The connecting dimensions of the flanges-according to GOST12815-80, type I.
Application
">">>
-
Features/advantages
-
Compared to pumps, cm allowed to work on liquids with sufficiently large impurities. The removal of the working wheel beyond the running part of the pump housing reduces the risk of jamming, and the clogging of the running part
Mark
Feed, m³/h
Ples, m
Permissible cavitation reserve, m
Rotation frequency, rpm
Pump power, kW
Voltage, in
PPD pump, %
The mass of the pump, kg
Pressure at the entrance to the pump, MPa
Current frequency, Hz
SMS 80-50-200
90
60
5
2900
35
220/380
54
75
0.25
50
SMS 150-125-315
200
32
7
1450
46
220/380
57
250
0.25
50
SMS free-vocal pumps and electric pump units on its basis are designed to pump urban and production waste masses and other non-aggressive liquids with a density of up to 1050 kg/m 3 with pH = 5-10, with temperature, with temperature. Up to 363k (90 ° C) of carrying fairly large extraneous objects and with the content of abrasive particles in size up to 5 mm. no more than 1% by mass. The maximum concentration of the pumped mass is 8%. The maximum gas content in the pumped environment is 5%.
Pumps can be used in other industries, if in their parameters and execution they satisfy the operating and safety conditions in these industries.
Pumps (units) belong to products of the type 1 (restored) according to GOST 27.003-90 and are produced in the climatic performance of UHL for operation in rooms of the placement category 4 according to GOST 15150-69 and climatic design of the placement of placement 2 according to GOST 15150-69.
SMS type pumps and electric pump units on their basis are not designed for installation in explosive and fire hazardous rooms.
Pumps and units are developed taking into account export delivery in accordance with the requirements of OST26-06-2011-79.
SMS type pumps - centrifugal, horizontal, console, with an ELD seal of the shaft.
The SMS pump housing is a cast-iron casting, in which the pump and output pipe, spiral-ring tap and supporting paws are entered. The entrance to the pump is located along the rotation axis, the output pipe is directed vertically upward and is located in the same plane with the wheel axis. SMS pumps and cm are the same.
The working wheel - free -wound type (open), is shifted in the axial direction relative to the spiral body of the pump, which allows the use of a pump for pumping liquids with fairly large foreign objects. The working wheel is attached to the shaft using a celestial nut.
The pump rotor is rotated by the electric motor through the connecting bushing-fan coupling. Rotor supports are two radially - stubborn bearing installed in the bracket.
The direction of rotation of the rotor is right (clockwise), if you look from the side of the electric motor.
The connecting dimensions of the flanges-according to GOST12815-80, type I.
Application
">">>
-
Features/advantages
-
Compared to pumps, cm allowed to work on liquids with sufficiently large impurities. The removal of the working wheel beyond the running part of the pump housing reduces the risk of jamming, and the clogging of the running part
Mark
Feed, m³/h
Ples, m
Permissible cavitation reserve, m
Rotation frequency, rpm
Pump power, kW
Voltage, in
PPD pump, %
The mass of the pump, kg
Pressure at the entrance to the pump, MPa
Current frequency, Hz
SMS 80-50-200
90
60
5
2900
35
220/380
54
75
0.25
50
SMS 150-125-315
200
32
7
1450
46
220/380
57
250
0.25
50
- ">">>
- Compared to pumps, cm allowed to work on liquids with sufficiently large impurities. The removal of the working wheel beyond the running part of the pump housing reduces the risk of jamming, and the clogging of the running part
Features/advantages
| Mark | Feed, m³/h | Ples, m | Permissible cavitation reserve, m | Rotation frequency, rpm | Pump power, kW | Voltage, in | PPD pump, % | The mass of the pump, kg | Pressure at the entrance to the pump, MPa | Current frequency, Hz |
| SMS 80-50-200 | 90 | 60 | 5 | 2900 | 35 | 220/380 | 54 | 75 | 0.25 | 50 |
| SMS 150-125-315 | 200 | 32 | 7 | 1450 | 46 | 220/380 | 57 | 250 | 0.25 | 50 |
