The unit is designed to supply a c/p of a mobility of at least 8 cm, determined by GOST 5802-86 and tall liquids with a viscosity of up to 300p (3x10 MPa C). The unit can be used to injure cement and one-component polyurethane compounds, as well as the supply of soils, adhesive and water-red paints.
The installation equipment is possible in two versions:
- Motor-reducer and two working pairs with a capacity of 0.84 m 3 /hour and 0.42 m 3 /hour, respectively;
- With a speed variator that allows you to provide a smooth supply with a minimum pulsation of the compositions to maximum.
The unit is equipped with a reception funnel (pos. 1) and a screw (pos. 2), Which supplies a liquid (mixture, solution) into the suction cavity of the pump (Ps.3). Due to the selection of the correct geometry “rotor (pos.4) -stator (pos.5)” and the supply of the screw, as well as the revolutions of its rotation, you can pump liquids and solutions with inclusions of solid fractions with a diameter of up to 1.5-3 mm. It is used on alcohols of industrial, civil and rural construction, secured by electricity. Climatic performance-V, Country Category-1 according to GOST 15150-69, according to electrical safety, the unit corresponds to GOST 12.2.007.0-75 and is made according to the protection class 1 (electrical equipment has a degree of protection IP 54)
Advantages:
- The width of the unit (510 mm) allows you to transport it through narrow doorways, and the turning large wheels make the installation very maneuverable at the construction site;
- Uniform supply of solutions (compositions);
- Dosage changes are achieved by a change in the rotor speed;
- The absence of suction and injection valves provides high reliability during operation;
- The supply of cement solutions with a mobility of at least 8 cm and high -skinned liquids;
- The ability to change the direction of the supply to the opposite.
an1VS -screw pump -a plaster station for pumping and Injections of cement and polyurethane compositions, primers, adhesive and water-red colors
The unit is designed to serve C/P solutions with a mobility of at least 8 cm, determined according to GOST 5802-86, and high-chick liquids with a viscosity of up to 300p (3x104 MPa*C) and with the inclusion of solid fractions up to 1 with a diameter of up to 1 , 5-3 mm . The unit can be used to injure cement and one-component polyurethane compounds, as well as the supply of soils, adhesive and water-red colors.
q = 0.84 (0.42) m3/hour ± 10%, p = 1.2MPA (12ATM), n = 70 rpm, n = 2.2 kW
The setting of the installation An1VS, screw pump - plaster station is possible in two versions:
-Motor-editor and two working pairs with a capacity of 0.84 m3/h and 0.42 m3/h, respectively;
-With a speed variator that allows you to provide a smooth supply with a minimum pulsation of the compositions to maximum.
The unit is equipped with a reception funnel (pos.5) and a screw (pos.3), which supplies a liquid (mixture, solution) into the suction cavity of the pump (Ps. 2).
Due to the selection of the correct geometry “Rotor (pos. 1)-Stator” and the supply of the screw (pos.3), as well as the revolutions of its rotation, you can pump liquids and solutions with inclusions of solid fractions with a diameter of up to 1.5-3 mm.
It is used at industrial, civil and rural construction facilities secured by electricity. Climate performance-V, Country category-1 according to GOST 15150-69, according to electrical safety, the unit corresponds to GOST 12.2.007.0-75 and is made according to the protection class 1 (electrical equipment has a degree of protection IP 54)
Advantages An1VS, screw pump - plaster station :
-
The width of the unit (640 mm) allows you to transport it through narrow doorways, and the turning large wheels make the installation very maneuverable at the construction site;
-
Uniform supply of solutions (compositions);
-
Dosage changes are achieved by a change in the rotor speed;
-
The absence of suction and injection valves provides high reliability during operation;
-
The supply of cement solutions with a mobility of at least 8 cm and high -skinned liquids;
-
The ability to change the direction of the supply to the opposite.
Technical characteristics An1VS, screw pump - plaster station :
Productivity-0.84 (0.42) M 3 /hour ± 10%
Working pressure - up to 1.2 MPa (12 ATM)
The number of rotation of the screw is 70 rpm
electric motor
(General -industrial performance (50Hz, IP54, U3):
Power -2.2 kW
The number of revolutions - 1,420 rpm
Voltage - 380 V
Dimensional dimensions - 1511 x 640 x 900 mm
Mass - 150 kg
