The vertical sludge pump of the VShN-150 is specially designed to work with abrasive pulps with a density of up to 1300 kg/cube. meter. The vertical sludge pump VShN-150 is characterized by a strong design, convenient in maintenance and repair.
The price of the VSHN-150 pump to a large extent contributes to the wide (mass) use of the pump in various industries.
The vertical sludge pump VShN-150 is designed on the basis of a horizontal console pump type GSHN.
Marking of the NSHN-150 pump includes the design features and performance of the pump-a vertical sludge pump with a capacity of 150 cubic meters. meters per hour.
The vertical sludge pump VShN-150 has a two blap open working wheel capable of passing solid particles in size up to 20 mm.
The vertical sludge pump of the VShN-150 at the installation site is attached with bolts through the supporting plate on the case. To ensure convenient access, the BSN-150 pump bearings are located in the housing above the supporting plate. The VShN-150 pump cannot work without load. The operation of the VShN-150 pump for dry without a pumped environment is not allowed.
By order, the vertical sludge pump VShN-150 can be made with an elongated shaft.
The shaft of the vertical sludge pump VShN-150 has a modular design, with
placing a bearing node above the supporting plate. In the NShN-150 pump there are no flooded bearings and shaft sealing oil seals. This design makes it easier for the maintenance of the VShN-150 pump and eliminates the need to use complex and expensive seals.
The shaft of the vertical sludge pump VShN-150 rotates in motionlessly fixed bearings lubricated by consistent lubricant.
Pump VShN-150/30 is designed for pumping:
- hydrosons (clay solutions, a mixture of water with sand, ore, etc.);
- household and industrial wastewater;
- spent flushing solution;
- hydraulic cyclone installation for cleaned breed;
- flushing solution used for drilling wells.
Characterization of the pumped environment:
- hydroxide density, up to 1,300 kg/cubic meter
- temperature, from +5 s to + 50 s
- content of solid particles, no more than 25 %
- max value of solid particles, no more than 20 mm
Technical characteristics of the NSH NSN 150/30:
SUMM - 150 m3/h;
Ples - 30 m;
The diameter of the working wheel is 360 mm;
Diameter of the pipe:
- suction - 125 mm
- pressure - 125 mm
Material:
- the running part - gray cast iron
- protective disk (armored vehicle) of the case - steel 40x
Dimensional dimensions - 1810x875x650 mm
The mass is no more - 620 kg;
Type of the working wheel - open;
Fastening - bolts on containers or design on order;
Electric drive:
- engine type - VA180M4
- explosion safety - 1ExDIIBT4X
- power - 30 kW
- Rotation frequency - 1,500 rpm
- degree of protection - ip54
pump vertical sludge owl 150/30
The console centrifugal vertical pump, single -stage with the working wheel of a unilateral entrance, with an axial fluid supply, with a drive from an electric motor through an elastic coupling. The working bodies are made of 40x steel.
The pump is designed for pumping:
abrasive hydrosons (clay and gravel solutions, a mixture of water with sand, ore, etc.);
flushing solution used for drilling wells;
household and industrial wastewater;
spent flushing solution into a hydraulic cyclone unit for cleaning from broken rock.
characteristics of the pumped environment:
Hydosmes density up to 1300 kg/m 3 ;
Temperature from +5 C to +60 CO;
The content of solid particles is not more than 25%;
The maximum value of solid particles is not more than 20 mm.
